 |
| Quantity: | |
|---|---|
BLS-01
Switch on the power, start the motor. Using an oilstone stained with ordinary lubricants completely polished shaft sleeve, press evenly oilstone with your thumb when polished, wipe motor shaft sleeve after polished, stop the motor. The purpose of polished is to eliminate the impact of original film or nanometer film on the experimental results.
1. Fix the friction block into the short lever groove of the testing machine,add ordinary lubricant oil into oil box, well-installed the lubricating oil box and the length of the lever.
2. Start the motor, firstly, let the motor run.Then at set intervals (such as 10 seconds),
plus the weight on long lever ends one by one, each weight is equal to the pressure of the friction pair carrying 100 kg. Record the number of weights, look at change in ammeter
pointer, the pointer increase, power consumption increase, fuel consumption also
increase. Noise increases, continue to add weight (about 3,4 blocks) until the wheel stops, the machine locking, quickly turn off the power. Remove the weights, remove the short
lever, observe the depth, area and roughness of grinding marks on cylindrical grinding
Switch on the power, start the motor. Using an oilstone stained with ordinary lubricants completely polished shaft sleeve, press evenly oilstone with your thumb when polished, wipe motor shaft sleeve after polished, stop the motor. The purpose of polished is to eliminate the impact of original film or nanometer film on the experimental results.
1. Fix the friction block into the short lever groove of the testing machine,add ordinary lubricant oil into oil box, well-installed the lubricating oil box and the length of the lever.
2. Start the motor, firstly, let the motor run.Then at set intervals (such as 10 seconds),
plus the weight on long lever ends one by one, each weight is equal to the pressure of the friction pair carrying 100 kg. Record the number of weights, look at change in ammeter
pointer, the pointer increase, power consumption increase, fuel consumption also
increase. Noise increases, continue to add weight (about 3,4 blocks) until the wheel stops, the machine locking, quickly turn off the power. Remove the weights, remove the short
lever, observe the depth, area and roughness of grinding marks on cylindrical grinding
Switch on the power, start the motor. Using an oilstone stained with ordinary lubricants completely polished shaft sleeve, press evenly oilstone with your thumb when polished, wipe motor shaft sleeve after polished, stop the motor. The purpose of polished is to eliminate the impact of original film or nanometer film on the experimental results.
1. Fix the friction block into the short lever groove of the testing machine,add ordinary lubricant oil into oil box, well-installed the lubricating oil box and the length of the lever.
2. Start the motor, firstly, let the motor run.Then at set intervals (such as 10 seconds),
plus the weight on long lever ends one by one, each weight is equal to the pressure of the friction pair carrying 100 kg. Record the number of weights, look at change in ammeter
pointer, the pointer increase, power consumption increase, fuel consumption also
increase. Noise increases, continue to add weight (about 3,4 blocks) until the wheel stops, the machine locking, quickly turn off the power. Remove the weights, remove the short
lever, observe the depth, area and roughness of grinding marks on cylindrical grinding
Switch on the power, start the motor. Using an oilstone stained with ordinary lubricants completely polished shaft sleeve, press evenly oilstone with your thumb when polished, wipe motor shaft sleeve after polished, stop the motor. The purpose of polished is to eliminate the impact of original film or nanometer film on the experimental results.
1. Fix the friction block into the short lever groove of the testing machine,add ordinary lubricant oil into oil box, well-installed the lubricating oil box and the length of the lever.
2. Start the motor, firstly, let the motor run.Then at set intervals (such as 10 seconds),
plus the weight on long lever ends one by one, each weight is equal to the pressure of the friction pair carrying 100 kg. Record the number of weights, look at change in ammeter
pointer, the pointer increase, power consumption increase, fuel consumption also
increase. Noise increases, continue to add weight (about 3,4 blocks) until the wheel stops, the machine locking, quickly turn off the power. Remove the weights, remove the short
lever, observe the depth, area and roughness of grinding marks on cylindrical grinding
